| The SolarOasis SunMount growing system makes it easy to mount multiple LED grow lights when using LGM3 plant lighting for larger grow areas. |
| Made of two pieces of strong, lightweight aluminum sheets. The SunMount requires no assembly. Each grow bar attaches securely with provided hardware, and a single SunMount will hold from four to eight bars. Recommended for LGM3 LED grow lights only. SunMount Retail Price $55.00 USD Buy Now |
| The LED grow lights on each SunMount growing system are aligned in a staggered configuration, ensuring maximum light delivery to your plants. With grow lights attached, a SunMount measures approximately two feet on each side. Special mounting tabs allow multiple SunMounts to be bolted together and make hanging a breeze. |
| (LED grow lights not included) |
Light Bar Frame Assembly and Use Instructions:
Assembly Overview-
The light bar frame assembles quickly and easily without tools. Fig. 1 shows a partially assembled frame, with light bars attached to the bottom side of the
two frame pieces. Each Light bar is attached with two push pin retainers, using just a push of the thumb. Note: Use the flat side of a penny or nickel
between your thumb and push pin head for easier assembly.
The light bar frame assembles quickly and easily without tools. Fig. 1 shows a partially assembled frame, with light bars attached to the bottom side of the
two frame pieces. Each Light bar is attached with two push pin retainers, using just a push of the thumb. Note: Use the flat side of a penny or nickel
between your thumb and push pin head for easier assembly.
Single Frame Assembly-
The light bar frame is assembled by attaching four or more light bars to the underside of the frame using the supplied push pin retainers. As shown in Fig.
2, place the first frame piece upside down, with the edge tab pointing down. Place the flat side of each light bar against the frame, aligning each hole in one
light bar end tab with a pre-drilled hole in the frame. Insert one push pin retainer through each hole from the light bar side. Press down on the button on
each push pin until fully depressed. The light bar is now firmly attached to the light bar frame. Once the push pin button has been depressed it cannot be
removed. Make sure you have aligned the bars properly before pushing the push pin button down.
Repeat the process with the second frame piece at the opposite end of the light bars. When fully assembled, one frame piece will be attached to each end
of the array of light bars, and each bar should be parallel to adjacent bars. Adjust frame/bar alignment as needed.
The light bar frame is assembled by attaching four or more light bars to the underside of the frame using the supplied push pin retainers. As shown in Fig.
2, place the first frame piece upside down, with the edge tab pointing down. Place the flat side of each light bar against the frame, aligning each hole in one
light bar end tab with a pre-drilled hole in the frame. Insert one push pin retainer through each hole from the light bar side. Press down on the button on
each push pin until fully depressed. The light bar is now firmly attached to the light bar frame. Once the push pin button has been depressed it cannot be
removed. Make sure you have aligned the bars properly before pushing the push pin button down.
Repeat the process with the second frame piece at the opposite end of the light bars. When fully assembled, one frame piece will be attached to each end
of the array of light bars, and each bar should be parallel to adjacent bars. Adjust frame/bar alignment as needed.
Tying One Frame to Another-
Your light bar frame is designed to allow multiple frames to be tied together to create a larger lighting panel. Frames may be attached either side-to-side
and/or end-to-end by following the instructions below.
Your light bar frame is designed to allow multiple frames to be tied together to create a larger lighting panel. Frames may be attached either side-to-side
and/or end-to-end by following the instructions below.
End-To-End Assembly-
To tie two frames end-to-end, align the vertical lifting tabs of two frames and, using three push pin retainers, attach the frames using the center tab hole and
two outermost tab holes as shown in Fig. 3. Be sure to only put push pin retainers into the center and outermost holes. The hole to the inside of the frame
attachment hole is for lifting the assembled frame using the supplied 'S' hooks.
To tie two frames end-to-end, align the vertical lifting tabs of two frames and, using three push pin retainers, attach the frames using the center tab hole and
two outermost tab holes as shown in Fig. 3. Be sure to only put push pin retainers into the center and outermost holes. The hole to the inside of the frame
attachment hole is for lifting the assembled frame using the supplied 'S' hooks.
| SunMount Lighting System |
 |
 |